{"product_id":"t-type-angle-pin-fixing-block","title":"T-Type Angle Pin Fixing Block","description":"\u003cp\u003e\u003cstrong\u003eT-type angle pin fixing blocks, made to your drawing.\u003c\/strong\u003e The T-form version, where a semicircular clamp or T-slot captures the pin against a machined seat. This page is about \u003cem\u003eload path\u003c\/em\u003e — where the sideways force from the pin actually goes, and how the T-form carries it. For the retention side (stopping the pin rotating or creeping), see our \u003ca href=\"\/products\/dy-angle-pin-fixing-block\"\u003eDY angle pin fixing block\u003c\/a\u003e; for the supporting seat under the pin root, see the \u003ca href=\"\/products\/t-type-angle-pin-seat\"\u003eT-type angle pin seat\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eWhy a T-form instead of a plain bored block\u003c\/h2\u003e\u003cp\u003eA plain block resists the pin's side load through the bolts and the friction of its own mounting face. A T-form puts a machined shoulder in the load path, so the force is carried by steel bearing against steel rather than by bolt preload. That matters as the mold ages: bolt preload relaxes, mounting faces fret, and a joint that was relying on friction starts to move. A shoulder does not relax.\u003c\/p\u003e\u003cp\u003eThe practical consequence when you specify one: \u003cstrong\u003ethe T-shoulder must be a proper fit against its pocket in the plate.\u003c\/strong\u003e A T-block sitting in an oversized pocket has all the disadvantages of a plain block plus more machining cost. Tell us the pocket dimensions and the fit you want, or send the plate drawing and we will work to it.\u003c\/p\u003e\u003ch2\u003eClamping the pin without distorting it\u003c\/h2\u003e\u003cp\u003eThe semicircular clamp has to grip the pin over its seated length, evenly. Two things to get right:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThe clamp radius should match the pin diameter, with the split slightly relieved.\u003c\/strong\u003e If the two halves close solid before they grip, the pin is loose no matter how tight the bolts are. If they grip only at the split line, you crush the pin's ground surface at two points.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBolt spacing decides how evenly the clamp closes.\u003c\/strong\u003e Two bolts far apart on a long clamp let the middle lift. Say how long the clamped length is and we will size the bolt layout with you.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eBore angle\u003c\/h2\u003e\u003cp\u003eAs with any angle pin mounting, the bore angle and the pin's working angle have to be the same number. A block bored a degree off seats the pin on a line, and that line is where the pin bends. Give the angle explicitly rather than leaving us to infer it — and on a mold that has been running, measure the pin rather than trusting the original drawing.\u003c\/p\u003e\u003ch2\u003eWhat to send us\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBlock length, width and height, and the T-shoulder dimensions\u003c\/li\u003e\n\u003cli\u003ePocket dimensions in the mating plate, and the fit you want on the shoulder\u003c\/li\u003e\n\u003cli\u003eBore diameter, bore angle and clamped length\u003c\/li\u003e\n\u003cli\u003eSemicircular clamp or plate geometry, split line and relief\u003c\/li\u003e\n\u003cli\u003eMounting-hole, thread and counterbore layout, and centre distances\u003c\/li\u003e\n\u003cli\u003eAngle pin diameter, length and current fixing method\u003c\/li\u003e\n\u003cli\u003eAssembly drawing where available; material, hardness, tolerance, quantity, destination\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDocumentation and confidentiality\u003c\/h2\u003e\u003cp\u003eMaterial certificates, hardness results and dimensional inspection reports are available, with scope and cost stated in the quotation. Technical files are used to evaluate and fulfill your inquiry or order. They may be shared only with relevant manufacturing, inspection, logistics or service partners as needed. Send only files you are authorized to share. See our \u003ca href=\"\/pages\/privacy-policy\"\u003ePrivacy Policy\u003c\/a\u003e. NDA on request from \u003ca href=\"mailto:rfq@privleymold.com\"\u003erfq@privleymold.com\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003e\"T-type\" identifies a configuration family rather than a dimensional standard — we quote from your dimensions and confirm the controlling ones before anything is made.\u003c\/em\u003e\u003c\/p\u003e","brand":"Privley Mold Components","offers":[{"title":"Default Title","offer_id":52126011523292,"sku":"PMC-APB-T","price":0.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0846\/7650\/9916\/files\/privley-t-type-angle-pin-fixing-block-rfq-diagram_43e55249-1b05-465c-8549-062df6939368.png?v=1785388366","url":"https:\/\/privleymold.com\/products\/t-type-angle-pin-fixing-block","provider":"Privley Mold Components","version":"1.0","type":"link"}